Mobile elevated platforms for construction

Mobile elevated platforms for construction

Products Features:

1) Multi-fuction. People can control the machines on the platform to walk, reverse, rise, fall or turn. It can propel fast or slow at different working height.

2) Strong and durable. It is composed by three parts, base, arm and platform.
Bases are made from strong steel plate.
Arm parts are scissor design with strong Manganese steel.
There is Guard railing on the platform to ensure people's safety.

Mobile elevated platforms for construction

3) Safety guaranteed.
The equipments are designed with over loading hydraulic security protection system and anti falling system in case of power shortage.
It was designed with a emergence valve for dropping in case of power shortage.

Available Models

Mobile elevated platforms for construction

Detail introduction for components

Mobile elevated platforms for construction

How to operate?

1. Ahead of its first use or the use after a long distance transportation, the hydraulic and electric systems must be checked to make sure that there is no leakage or wire connection loose.

2.Fill hydraulic oil full into hydraulic oil tank. Anti–abrasive oil 32# is used in the winter and 46# is used in the summer.

3.Open the supporting legs: when using movable lift, four supporting legs should be firmly supported in the solid ground surface. Wood sleepers could be applied to adjust the equipment to the horizon level when necessary(this can be checked visually).

Warning : Prohibit use before open supporting leg

4.Try the lift:

A. Press the " Up" button on the push button switch and then stop the lift, operator should check whether the hydraulic line, every connector and electrical lines have leakage, scraping and oppressed phenomenon or not. When the lift is used in the first time or changed use place, operator should repeat this process.

B. Press the " Down" button, the lift goes down.

5.The lift not in use for a long time can be used again after it works for 1 to 3 cycles without any load on it.

6.The load’s barycenter need to be in the center of the working platform as possible as it can.

7.The dodge gate of the guardrail on the platform need to be closed and locked correctly before each use.

Mobile elevated platforms for construction

Daily maintenance

1.The lift shall be operated and maintained by the designated person.

2. Replace the oil once every six months. Anti –abrade hydraulic oil No.32 is used in the winter time and No. 46 is used in the summer time.

3. Check the lubricating situation on the hinged connection and lubricate these parts as scheduled to avoid dry-friction between the connected parts.

4.When not in use, the lift shall be stored properly and not be allowed to be put in the open air, it is better to cover a shield on the equipment. The supporting legs are close.

-Wide chassis makes the lower part of the Equipment which can bear the load balance to enhance stability.
-355/55D625 Solid Tyre, Mobile elevated platforms for construction can keep stable not only in a variety of complex conditions but also enhance the ground friction then mobile platform lift is more stable in operation and climbing easier.
-mobile platform lift The steering system adopts double oil cylinder and Hydra steering system with 40Cr steering linkage to ensure the same direction.
-Floating leveling device will start automatically when the device encountered under the condition of uneven groundto ensure the balance of equipment Mobile elevated platforms for construction with slope of 6 degrees then strengthen the safety and adaptability.
DFGXSDFGBA
-360°continuous rotationwith 50Cr rotary support
-Emergency safety pump. mobile platform lift The operator can use emergency safety pump to fall safelywhen the equipment is working at high altitude which can not be down.
-Constant pressure pump of Danfoss USA or Rexroth Germanit avoid oil leakage caused by gear pump damage in long -term construction
-Mobile elevated platforms for construction of centralized electric control box is used to ensure the safety of equipment operation
-Ground control console and platform control console the former has a large screen display with self diagnostic screen without connected mobile platform lift to the computerthen customers can easily understand the calibration status of equipment and parameters which is convenient debugging and testing.
-Controller of IFM Germany can enhance system stability
-Turntable safety lockto avoid the damage in the transport mobile platform lift and maintenance of arm rotation
-Swing-out engine bracket - provide the world industry closest to the engine design easy maintenance and repairs.
-Glass fiber Mobile elevated platforms for construction steel cover make the whole equipment nice and durable